No thumbscrew to swivel it, but it has some sort of friction washer where the yoke meets the base. On that same note, dating sites there is nothing wrong with leaving them alone. Prices vary depending on condition and other factors.
Here is a thread on our Antique Fan Collectors Association forum that should be of help to you and your pancake. Swivel bracket has old repair. The large blades are not original to this fan. The first pancakes from through the middle of had a single speed motor. The wiring on the fan is original factory wiring.
Ceiling Fan Emerson fan Ceiling fans
International Association of Certified Home Inspectors. Thank you for making this information available. All wiring is within the base going up to the motor which is a rigid part of the motor casting. These coils just fell out when I was inspecting and cleaning the motor.
The motor was still devoid of the vent holes that would appear on the models. The motor now sported three instead of four cage struts with one strut located at the top of the motor and the others at the lower sides of the motor. The brushes are good and armature was polished to assure good contact with brushes. The motor was disassembled, cleaned, inspected, windings were revarnished and motor was oiled.
The oscillating mechanism is hidden entirely inside the bullet rear cover. The only difference is Form letter. The base appears to be black or very dark green.
None of my Emerson bulletins mention anything pertaining to this fan dating system. Research guru extraordinaire Russ Huber sent me this copy of a Emerson spare parts guide. It uses Emerson's unique hollow stationary shaft single bearing. This fan uses Emerson's unique hollow stationary shaft single bearing.
30 Best Emerson Fans History images in
They started producing desk fans in and in marketed their first ceiling fan. You'll note it has wide blades like the C Cat. Any idea what year this would be? It's one of the later versions. We have completely restored this one cleaning and lubing motor and refinishing gloss black cast iron base and body.
New for 2019
- Note the three voltages that each fan was offered in.
- Again another very educational posting about an early fan.
- In the days before the fans were convertible from desk to bracket fans beginning with the Type a separate bracket Type model was offered differing only in the base of the fan motor.
- If there are no reproduction of an original pancake switch that should work fine.
- The motor tag remained of plain brass with all the data stamped in it.
- Both models were offered in most years starting c.
- From the Great Depression of the s, until the introduction of electric air conditioning in the s, ceiling fans slowly faded out of vogue in the U.
- The page to the right and those below are from an Emerson catalog dated Jan.
- Motor housings are sleeker now without the dome in the rear cover.
- It turned out great and this fan will be on display, and For Sale, at our next annual antique fan show coming up in April.
- Motor bearings have no play.
Good workhouse fans of the later s. Unlike modern rotary fans, these punkah fans move air by moving to and from, and were operated manually by cord. As far as early fans go, they are common enough so they can be found at a somewhat high but still affordable cost. Will at times run at speed, but is inconsistent. New Grommets and felt feet were also put on.
They cool people effectively by introducing slow movement into the otherwise still, hot air of a room. By the s, ceiling fans were commonplace in the United States, and had started to take hold internationally. An oil return collar was now press fitted to the front of the motor in front of the bearing to catch oil thrown from the grooves on the blade hub and direct it back into the top of the oiler. Please help improve it or discuss these issues on the talk page.
Hi Larry, the Emerson is a scarce and very nice earlier Emerson and I wish you luck on your restoration. They are long ago sold out and, with a good demand for pancake switches, I think you will see some available in the next year. That alone would greatly decrease the value.
The portion entering the rear ring was narrowed down slightly to fit a hole drilled in the ring, the wire was inserted and then slightly peened over to make the wire tight. Change from cast hub to stamped hub blade during production. The white porcelain switch is unusual and the only one of two that I am aware of. The owner sent me these huge photos and, with his permission, best generic first message I post them here. Another concern with installing a ceiling fan relates to the height of the blades relative to the floor.
Please read the notes on contacting me on the Main Page. Hunter fans made before will say Fulton, N. It is a model and is a great fan for daily use.
Anyone want to help me out wiht an estimated value? Please improve it by verifying the claims made and adding inline citations. Swivel frame models used a brass band tag nearly encircling the motor in place of the shorter brass tag used on trunnion motors.
The two speed switch knob is at the bottom of the wall base. Quiet for a large volume fan. Lightly cleaned and original!
Usually they are missing or badly worn. Thank you John Fetner for these photos and for selling me this nice original and smooth running pancake. With the exception of some wear to the base, benefits of the finish is in great shape. The is a highly desirable and rare fan and usually fairly high priced. This particular piston and rod is from an engine manufactured in and was used for marine propulsion navy battleship.
Other American manufacturers of the time included the Hunter Fan Co. Dek I have pics of the fan I could send. Everything is about function over form.
In very rare case, such as late Hunter Original, fans are both mechanically reversible and electrically reversible, in which case it can blow air up, or down, in either direction. Unique to these two years was a fancy cast and nickel plated name plate on the rear of the motor. With a serial number prefixed by a T, it is one of the last serial-numbered Emerson fans.
When you look at a Lynn Works, you have to marvel at the simplicity. The poor thing has survived being submerged at some point in it's life. Moves a lot of air for it's size. Ask if anyone has a pancake near your number and what material the struts are made of. Looking behind the cage badge you will see the brass disc used for the past few years which is held in place by the small crimps around the outside of the rear of the badge.
There's the early models, with full ribbed bases that now housed the switch and coil. This article has multiple issues. Please help improve this section by adding citations to reliable sources. There is a nut of sorts on the front of the rotor bearing after you get the fan blade off which, in itself, can be quite a chore. Due to the different construction of the motors between the two frame styles, the motor tags were different until, I think, the models where the same tags appears to have been used.
Vintage Emerson Fans
As you can see, mine is missing some oscillator parts. In other projects Wikimedia Commons. This fan was found about miles from where I am located. The brass identification plate is mounted on the base, just below the switch. Like Chris says, with a bit of paint and some imagination, these can be made to look Hot.